Overview
This unit will introduce you to the fundamentals of industrial instrumentation and automation systems. You will learn the principles of operation of different sensors, actuators, instrumentation amplifiers, and industrial data communication busses. You will also learn noise cancellation and signal conditioning, sensor and actuator interfacing, programmable logic controller (PLC) programming, and process control. You will learn how to specify the requirements for sensors, actuators, and control equipment for a given task, evaluate multiple options available, and select the best combination of them for your design. You will also design, fabricate, and program production lines for a given product using industry standard components and PLCs. You will carry out product line programming using a simulated software environment.
Details
Pre-requisites or Co-requisites
Prerequisites: ENEX12002 Introductory Electronics OR (ENEE13018 Analogue Elecctronics & ENEE13020 Digital Electronics ) AND ENEE12016 Signals and Systems
Important note: Students enrolled in a subsequent unit who failed their pre-requisite unit, should drop the subsequent unit before the census date or within 10 working days of Fail grade notification. Students who do not drop the unit in this timeframe cannot later drop the unit without academic and financial liability. See details in the Assessment Policy and Procedure (Higher Education Coursework).
Offerings For Term 2 - 2020
Attendance Requirements
All on-campus students are expected to attend scheduled classes - in some units, these classes are identified as a mandatory (pass/fail) component and attendance is compulsory. International students, on a student visa, must maintain a full time study load and meet both attendance and academic progress requirements in each study period (satisfactory attendance for International students is defined as maintaining at least an 80% attendance record).
Recommended Student Time Commitment
Each 6-credit Undergraduate unit at CQUniversity requires an overall time commitment of an average of 12.5 hours of study per week, making a total of 150 hours for the unit.
Class Timetable
Assessment Overview
Assessment Grading
This is a graded unit: your overall grade will be calculated from the marks or grades for each assessment task, based on the relative weightings shown in the table above. You must obtain an overall mark for the unit of at least 50%, or an overall grade of 'pass' in order to pass the unit. If any 'pass/fail' tasks are shown in the table above they must also be completed successfully ('pass' grade). You must also meet any minimum mark requirements specified for a particular assessment task, as detailed in the 'assessment task' section (note that in some instances, the minimum mark for a task may be greater than 50%). Consult the University's Grades and Results Policy for more details of interim results and final grades.
All University policies are available on the CQUniversity Policy site.
You may wish to view these policies:
- Grades and Results Policy
- Assessment Policy and Procedure (Higher Education Coursework)
- Review of Grade Procedure
- Student Academic Integrity Policy and Procedure
- Monitoring Academic Progress (MAP) Policy and Procedure - Domestic Students
- Monitoring Academic Progress (MAP) Policy and Procedure - International Students
- Student Refund and Credit Balance Policy and Procedure
- Student Feedback - Compliments and Complaints Policy and Procedure
- Information and Communications Technology Acceptable Use Policy and Procedure
This list is not an exhaustive list of all University policies. The full list of University policies are available on the CQUniversity Policy site.
Feedback, Recommendations and Responses
Every unit is reviewed for enhancement each year. At the most recent review, the following staff and student feedback items were identified and recommendations were made.
Feedback from Student survey
The labs with MPS systems were very interesting and relevant.
The Laboratory experiments will be the same for future offerings.
Feedback from Student survey
PLC programing is a valuable skill developed through this unit.
The Laboratory experiments with PLC programming will be the same for future offering.
Feedback from Student survey
It would be helpful if more guidance is provided for laboratory report writing.
More specific guidelines will be provided about the laboratory report writing.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
Learning outcomes are linked to Engineers Australia Stage 1 Competencies and also discipline capabilities. You can find the mapping for this on the Engineering Undergraduate Course website.
Alignment of Assessment Tasks to Learning Outcomes
| Assessment Tasks | Learning Outcomes | ||||||
|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | |
| 1 - Written Assessment - 20% | |||||||
| 2 - Written Assessment - 20% | |||||||
| 3 - Practical Assessment - 20% | |||||||
| 4 - Take Home Exam - 40% | |||||||
Alignment of Graduate Attributes to Learning Outcomes
| Graduate Attributes | Learning Outcomes | ||||||
|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | |
| 1 - Communication | |||||||
| 2 - Problem Solving | |||||||
| 3 - Critical Thinking | |||||||
| 4 - Information Literacy | |||||||
| 5 - Team Work | |||||||
| 6 - Information Technology Competence | |||||||
| 7 - Cross Cultural Competence | |||||||
| 8 - Ethical practice | |||||||
| 9 - Social Innovation | |||||||
| 10 - Aboriginal and Torres Strait Islander Cultures | |||||||
Alignment of Assessment Tasks to Graduate Attributes
| Assessment Tasks | Graduate Attributes | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | |
| 1 - Written Assessment - 20% | ||||||||||
| 2 - Written Assessment - 20% | ||||||||||
| 3 - Practical Assessment - 20% | ||||||||||
| 4 - Take Home Exam - 40% | ||||||||||
Textbooks
Principles of Measurement Systems
Edition: 4th (2005)
Authors: John P Bentley
Pearson Education Ltd.
Harlaw Harlaw , Essex , England
ISBN: 0-130-43028-5
Binding: Paperback
Additional Textbook Information
If you prefer to study with a paper copy, they are available at the CQUni Bookshop here: http://bookshop.cqu.edu.au (search on the Unit code). eBooks are available at the publisher's website.
IT Resources
- CQUniversity Student Email
- Internet
- Unit Website (Moodle)
- A portable computer with Windows 7 or later with Admin authority to install CoDeSys and other required software
- Access to a document scanner and a software that can create pdf documents
All submissions for this unit must use the referencing style: Harvard (author-date)
For further information, see the Assessment Tasks.
d.preethichandra@cqu.edu.au
Module/Topic
- Introduction to measurement systems, static characteristics, and accuracy of measurements
Chapter
- CH 1
- CH 2
- CH 3
Events and Submissions/Topic
Module/Topic
- Operational amplifiers in instrumentation systems
Chapter
- Lecture notes / slides
Events and Submissions/Topic
Module/Topic
- Introduction to Industrial Automation
- Fundamentals of Pneumatic System Elements
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- PLC Programming Fundamentals
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- Signal Conditioning Elements
Chapter
- CH 9
- Lecture notes/Slides
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
- Loading Effects in Two-port Networks
Chapter
-
CH 5
Events and Submissions/Topic
Module/Topic
- Signals and Noise in Measurement Systems
- Four Terminal Measurements and Source-Measure Units in Instrumentation Systems
Chapter
- Ch 6
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- Two-Port network parameters
- Data Acquisition and Communications Systems
- Industrial Data Communications Protocols
Chapter
- Lecture notes/ Slides
- CH18
Events and Submissions/Topic
Module/Topic
- Industrial Instrumentation Busses and their Applications
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
-
Industrial Process Control Systems
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Residential School 23-25 September
Assignment 2 Due: Week 10 Friday (25 Sept 2020) 11:55 pm AEST
Module/Topic
- Sensing Elements
- Ultrasonic Measurement Systems
- Flow Measurement Systems
Chapter
- Ch 8
- CH 16
- CH 12
Events and Submissions/Topic
Module/Topic
-
Parasitic Elements in Measurement
Sysems - Optical Measurement Systems
Chapter
- CH 14
- CH 15
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Due to COVID-19 situation the Res-School will not be held in face-to-face mode and it will be replaced by an online activity. However, the res-school schedule will not be changed and all students(on-campus and MIX mode) will be attending the res-scoohl together. There will not be any weekly practical sessions for on-campus studnets. The examination is replaced by a Take Home Examination.
1 Written Assessment
This assignment is based on instrumentation principles and application of them in actual measurement systems. Further details will be available on the unit moodle site.
Week 6 Friday (28 Aug 2020) 11:55 pm AEST
Week 9 Monday (14 Sept 2020)
Marked assignment with feedback will be provided.
Marks will be allocated for the following things:
1. Application of theoretical fundamentals.
2. Correct diagrams using standard notations.
3. Explanation of reasons to apply specific theory to solve a given problem where applicable.
4. Correct mathematical working and correct answer.
5. All working must be shown to obtain full marks
6. Neatness and format.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Implement complete solutions for industrial process automation problems
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
- Communication
- Problem Solving
- Critical Thinking
- Information Technology Competence
2 Written Assessment
This assignment is based on advanced measurement techniques and fundamentals of industrial automation systems.
Week 10 Friday (25 Sept 2020) 11:55 pm AEST
Week 12 Friday (9 Oct 2020)
Marked assignment with feedback will be provided.
Marks will be allocated for the following things:
1. Application of theoretical fundamentals.
2. Correct diagrams using standard notations.
3. Explanation of reasons to apply specific theory to solve a given problem where applicable.
4. Correct mathematical working and correct answer.
5. All working must be shown to obtain full marks
6. Neatness and format.
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
- Communication
- Problem Solving
- Critical Thinking
- Information Technology Competence
3 Practical Assessment
This task involves laboratory experiments on industrial automation and instrumentation (due to COVID-19 restrictions these hands-on lab exercises will be replaced by simulations). You will have to complete the pre-lab exercises to commence the laboratory practicals. Further details will be available in the unit moodle site.
Week 11 Wednesday (30 Sept 2020) 11:55 pm AEST
Review/Exam Week Wednesday (14 Oct 2020)
Marked lab reports with feedback.
Marks will be allocated to :
1. Active contribution in group work (if applicable)
2. Following the correct procedures during the experimentation.
3. Correct results.
4. Analysis of results and discussion.
5. Conclusions.
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
- Communication
- Problem Solving
- Critical Thinking
- Team Work
- Information Technology Competence
- Ethical practice
4 Take Home Exam
No Assessment Task Description
Take Home Examination will be held during the University examination period
Marks will be allocated for the following things:
1. Application of theoretical fundamentals.
2. Correct diagrams using standard notations.
3. Explanation of reasons to apply specific theory to solve a given problem where applicable.
4. Correct mathematical working and correct answer.
5. All working must be shown to obtain full marks
6. Neatness and format.
More specific details will be in the examination paper itself.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Communication
- Problem Solving
- Critical Thinking
- Information Technology Competence
- Ethical practice
As a CQUniversity student you are expected to act honestly in all aspects of your academic work.
Any assessable work undertaken or submitted for review or assessment must be your own work. Assessable work is any type of work you do to meet the assessment requirements in the unit, including draft work submitted for review and feedback and final work to be assessed.
When you use the ideas, words or data of others in your assessment, you must thoroughly and clearly acknowledge the source of this information by using the correct referencing style for your unit. Using others’ work without proper acknowledgement may be considered a form of intellectual dishonesty.
Participating honestly, respectfully, responsibly, and fairly in your university study ensures the CQUniversity qualification you earn will be valued as a true indication of your individual academic achievement and will continue to receive the respect and recognition it deserves.
As a student, you are responsible for reading and following CQUniversity’s policies, including the Student Academic Integrity Policy and Procedure. This policy sets out CQUniversity’s expectations of you to act with integrity, examples of academic integrity breaches to avoid, the processes used to address alleged breaches of academic integrity, and potential penalties.
What is a breach of academic integrity?
A breach of academic integrity includes but is not limited to plagiarism, self-plagiarism, collusion, cheating, contract cheating, and academic misconduct. The Student Academic Integrity Policy and Procedure defines what these terms mean and gives examples.
Why is academic integrity important?
A breach of academic integrity may result in one or more penalties, including suspension or even expulsion from the University. It can also have negative implications for student visas and future enrolment at CQUniversity or elsewhere. Students who engage in contract cheating also risk being blackmailed by contract cheating services.
Where can I get assistance?
For academic advice and guidance, the Academic Learning Centre (ALC) can support you in becoming confident in completing assessments with integrity and of high standard.
What can you do to act with integrity?
