Overview
This unit will introduce you to the fundamentals of industrial instrumentation and automation systems. You will learn the principles of operation of different sensors, actuators, instrumentation amplifiers, and industrial data communication buses. You will also learn noise cancellation and signal conditioning, sensor and actuator interfacing, programmable logic controller (PLC) programming, and process control. You will learn how to specify the requirements for sensors, actuators, and control equipment for a given task, evaluate multiple options available and select the best combination of them for your design. You will also design, fabricate, and program production lines for a given product using industry-standard components and PLCs. You will carry out product line programming using industry-standard PLC programming software and hardware. In this unit, you must complete compulsory practical activities. Refer to the Engineering Undergraduate Course Moodle site for proposed dates.
Details
Pre-requisites or Co-requisites
Prerequisites: ENEX12002 Introductory Electronics OR (ENEE13018 Analogue Elecctronics & ENEE13020 Digital Electronics ) AND ENEE12016 Signals and Systems
Important note: Students enrolled in a subsequent unit who failed their pre-requisite unit, should drop the subsequent unit before the census date or within 10 working days of Fail grade notification. Students who do not drop the unit in this timeframe cannot later drop the unit without academic and financial liability. See details in the Assessment Policy and Procedure (Higher Education Coursework).
Offerings For Term 2 - 2022
Attendance Requirements
All on-campus students are expected to attend scheduled classes – in some units, these classes are identified as a mandatory (pass/fail) component and attendance is compulsory. International students, on a student visa, must maintain a full time study load and meet both attendance and academic progress requirements in each study period (satisfactory attendance for International students is defined as maintaining at least an 80% attendance record).
Recommended Student Time Commitment
Each 6-credit Undergraduate unit at CQUniversity requires an overall time commitment of an average of 12.5 hours of study per week, making a total of 150 hours for the unit.
Class Timetable
Assessment Overview
Assessment Grading
This is a graded unit: your overall grade will be calculated from the marks or grades for each assessment task, based on the relative weightings shown in the table above. You must obtain an overall mark for the unit of at least 50%, or an overall grade of 'pass' in order to pass the unit. If any 'pass/fail' tasks are shown in the table above they must also be completed successfully ('pass' grade). You must also meet any minimum mark requirements specified for a particular assessment task, as detailed in the 'assessment task' section (note that in some instances, the minimum mark for a task may be greater than 50%). Consult the University's Grades and Results Policy for more details of interim results and final grades.
All University policies are available on the CQUniversity Policy site.
You may wish to view these policies:
- Grades and Results Policy
- Assessment Policy and Procedure (Higher Education Coursework)
- Review of Grade Procedure
- Student Academic Integrity Policy and Procedure
- Monitoring Academic Progress (MAP) Policy and Procedure - Domestic Students
- Monitoring Academic Progress (MAP) Policy and Procedure - International Students
- Student Refund and Credit Balance Policy and Procedure
- Student Feedback - Compliments and Complaints Policy and Procedure
- Information and Communications Technology Acceptable Use Policy and Procedure
This list is not an exhaustive list of all University policies. The full list of University policies are available on the CQUniversity Policy site.
Feedback, Recommendations and Responses
Every unit is reviewed for enhancement each year. At the most recent review, the following staff and student feedback items were identified and recommendations were made.
Feedback from Student feedback survey
The tutorials were highly relevant to the assignment questions and the exam.
This practice will be continued.
Feedback from Student feedback survey
Students say they were extremely comfortable with the exam after reviewing the given material.
This practice will be continued.
Feedback from Student feedback survey
The Lab was really engaging and interesting. The Festo machine was fun to program and apply troubleshooting skills to determine what sequence of ladder logic will perform certain tasks.
This practice will be continued.
Feedback from Student feedback survey
The written tutorial solution is difficult to understand and a video recording of the tutorial solution will help students to learn.
Video recording of the tutorial will be provided.
Feedback from Student feedback survey
More modern network protocols need to be taught instead of old protocols.
The older network protocols are taught to make the students understand the underlying theories. Newer industrial protocols will be added.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real-life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
The Learning Outcomes for this unit are linked with the Engineers Australia Stage 1 Competency Standards for Professional Engineers in the areas of 1. Knowledge and Skill Base, 2. Engineering Application Ability and 3. Professional and Personal Attributes at the following levels:
Intermediate
Advanced
Refer to the Engineering Undergraduate Course Moodle site for further information on the Engineers Australia's Stage 1 Competency Standard for Professional Engineers and course level mapping information
Alignment of Assessment Tasks to Learning Outcomes
Assessment Tasks | Learning Outcomes | ||||||
---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | |
1 - Written Assessment - 20% | |||||||
2 - Written Assessment - 20% | |||||||
3 - Practical Assessment - 20% | |||||||
4 - Online Test - 40% |
Alignment of Graduate Attributes to Learning Outcomes
Graduate Attributes | Learning Outcomes | ||||||
---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | |
1 - Communication | |||||||
2 - Problem Solving | |||||||
3 - Critical Thinking | |||||||
4 - Information Literacy | |||||||
5 - Team Work | |||||||
6 - Information Technology Competence | |||||||
7 - Cross Cultural Competence | |||||||
8 - Ethical practice | |||||||
9 - Social Innovation | |||||||
10 - Aboriginal and Torres Strait Islander Cultures |
Textbooks
Principles of Measurement Systems
Edition: 4th (2005)
Authors: John P Bentley
Pearson Education Ltd.
Harlaw Harlaw , Essex , England
ISBN: 0-130-43028-5
Binding: Paperback
IT Resources
- CQUniversity Student Email
- Internet
- Unit Website (Moodle)
- A portable computer with Windows 7 or later with Admin authority to install CoDeSys and other required software
- Access to a document scanner and a software that can create pdf documents
All submissions for this unit must use the referencing style: Harvard (author-date)
For further information, see the Assessment Tasks.
l.bui@cqu.edu.au
Module/Topic
- Introduction to measurement systems, static characteristics, and accuracy of measurements
Chapter
- CH 1
- CH 2
- CH 3
Events and Submissions/Topic
Module/Topic
- Operational amplifiers in instrumentation systems
Chapter
- Lecture notes / slides
Events and Submissions/Topic
Module/Topic
- Introduction to Industrial Automation
- Fundamentals of Pneumatic System Elements
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- PLC Programming Fundamentals
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- Signal Conditioning Elements
Chapter
- CH 9
- Lecture notes/Slides
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
- Loading Effects in Two-port Networks
Chapter
-
CH 5
Events and Submissions/Topic
Module/Topic
- Signals and Noise in Measurement Systems
- Four Terminal Measurements and Source-Measure Units in Instrumentation Systems
Chapter
- Ch 6
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- Two-Port network parameters
- Data Acquisition and Communications Systems
- Industrial Data Communications Protocols
Chapter
- Lecture notes/ Slides
- CH18
Events and Submissions/Topic
Module/Topic
- Industrial Instrumentation Busses and their Applications
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Residential School 14-16 September
Module/Topic
- Industrial Process Control Systems
- Introduction to Industry 4.0
Chapter
- Lecture notes/ Slides
Events and Submissions/Topic
Module/Topic
- Sensing Elements
- Ultrasonic Measurement Systems
- Flow Measurement Systems
Chapter
- Ch 8
- CH 16
- CH 12
Events and Submissions/Topic
Module/Topic
-
Parasitic Elements in Measurement
Sysems - Optical Measurement Systems
Chapter
- CH 14
- CH 15
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
You will conduct practical experiments during the compulsory residential school which will be held in Mackay Campus from Wednesday 14th to Friday 16th of September 2022. Further information about the residential school for this unit can be found on the handbook and the unit Moodle.
1 Written Assessment
This assignment is based on instrumentation principles and application of them in actual measurement systems. Further details will be available on the unit moodle site.
Week 7 Monday (29 Aug 2022) 11:59 pm AEST
Marked reports with feedback will be returned to students usually a fortnight after submission. However, there will be no model answers provided.
Marks will be allocated for the following things:
1. Application of theoretical fundamentals.
2. Correct diagrams using standard notations.
3. Explanation of reasons to apply specific theory to solve a given problem where applicable.
4. Correct mathematical working and correct answer.
5. All working must be shown to obtain full marks
6. Neatness and format.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Implement complete solutions for industrial process automation problems
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
2 Written Assessment
This assignment is based on advanced measurement techniques and fundamentals of industrial automation systems.
Week 10 Monday (19 Sept 2022) 11:59 pm AEST
Marked reports with feedback will be returned to students usually a fortnight after submission. However, there will be no model answers provided.
Marks will be allocated for the following things:
1. Application of theoretical fundamentals.
2. Correct diagrams using standard notations.
3. Explanation of reasons to apply specific theory to solve a given problem where applicable.
4. Correct mathematical working and correct answer.
5. All working must be shown to obtain full marks
6. Neatness and format.
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real-life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
3 Practical Assessment
This task involves laboratory experiments on industrial automation and instrumentation. You will have to complete the pre-lab exercises to commence the laboratory practicals. Further details will be available on the unit moodle site.
Week 11 Monday (26 Sept 2022) 11:59 pm AEST
Marked lab reports with feedback will be returned to students usually a fortnight after submission. However, there will be no model answers provided.
Marks will be allocated to :
- Active contribution in group work (if applicable)
- Following the correct procedures during the experimentation.
- Correct results.
- Analysis of results and discussion.
- Conclusions.
- Report structure.
- Apply common industrial data bus protocols and use them in data acquisition and control programs
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Program industrial PLCs to provide real-time solutions for industrial automation problems
- Implement complete solutions for industrial process automation problems
- Solve real-life problems and communicate professionally using instrumentation engineering terminology, symbols and diagrams that conform to Australian and international standards
- Work individually and collaboratively in teams, communicate professionally in presenting your solutions.
4 Online Test
This is the final assessment in the unit and it will be an online written test of three (3) hours. This online test is a time-limited assessment that will be available to students only during the scheduled examination time. It will be an open-book test and students can use any printed or electronic materials as a reference. The answers should be handwritten and scanned after the examination in the question order and uploaded by the given deadline.
Test date, time and test instructions will be provided to students at time closer to the test.
Marks will be released after the day of the certification of grades.
Marks will be allocated for the following things:
- Application of theoretical fundamentals.
- Correct diagrams using standard notations.
- Explanation of reasons to apply specific theory to solve a given problem where applicable.
- Correct mathematical working and correct answer.
- All working must be shown to obtain full marks.
- Neatness and format.
- Describe the need for instrumentation amplifiers in an instrumentation system and their operation
- Specify requirements for sensors, actuators, and accessories for a given process automation module, and select suitable components from a range of available options
- Implement complete solutions for industrial process automation problems
As a CQUniversity student you are expected to act honestly in all aspects of your academic work.
Any assessable work undertaken or submitted for review or assessment must be your own work. Assessable work is any type of work you do to meet the assessment requirements in the unit, including draft work submitted for review and feedback and final work to be assessed.
When you use the ideas, words or data of others in your assessment, you must thoroughly and clearly acknowledge the source of this information by using the correct referencing style for your unit. Using others’ work without proper acknowledgement may be considered a form of intellectual dishonesty.
Participating honestly, respectfully, responsibly, and fairly in your university study ensures the CQUniversity qualification you earn will be valued as a true indication of your individual academic achievement and will continue to receive the respect and recognition it deserves.
As a student, you are responsible for reading and following CQUniversity’s policies, including the Student Academic Integrity Policy and Procedure. This policy sets out CQUniversity’s expectations of you to act with integrity, examples of academic integrity breaches to avoid, the processes used to address alleged breaches of academic integrity, and potential penalties.
What is a breach of academic integrity?
A breach of academic integrity includes but is not limited to plagiarism, self-plagiarism, collusion, cheating, contract cheating, and academic misconduct. The Student Academic Integrity Policy and Procedure defines what these terms mean and gives examples.
Why is academic integrity important?
A breach of academic integrity may result in one or more penalties, including suspension or even expulsion from the University. It can also have negative implications for student visas and future enrolment at CQUniversity or elsewhere. Students who engage in contract cheating also risk being blackmailed by contract cheating services.
Where can I get assistance?
For academic advice and guidance, the Academic Learning Centre (ALC) can support you in becoming confident in completing assessments with integrity and of high standard.