Overview
This unit will introduce you to the fundamental synthesis of mechanisms and machines. You will start by carrying out analysis of linkages in terms of their transmission angles, toggle positions and mobility for a certain mechanism. The kinematic analysis of any mechanism requires an acceleration analysis that depends on its position and velocity. You will be able to carry out this position, velocity, and acceleration analysis of these mechanisms (kinematic systems) using analytical equations and graphical methods. This unit will enable you to work on 3D CAD modelling and computer simulation of various mechanisms or machines. You will move on to kinetic analysis of systems thereby discussing static and dynamic balancing of rotating masses. After learning concepts of dynamics, you will study vibrations (free and forced) of single and multi-degree of freedom systems and will be able to carry out analysis of such systems using force and energy methods. In this unit, you must complete compulsory practical activities. Refer to the Engineering Undergraduate Course Moodle site for proposed dates.
Details
Pre-requisites or Co-requisites
MATH11219 Applied Calculus AND [ENEM12007 Statics & Dynamics OR ENEM12010 Engineering Dynamics].
Important note: Students enrolled in a subsequent unit who failed their pre-requisite unit, should drop the subsequent unit before the census date or within 10 working days of Fail grade notification. Students who do not drop the unit in this timeframe cannot later drop the unit without academic and financial liability. See details in the Assessment Policy and Procedure (Higher Education Coursework).
Offerings For Term 1 - 2024
Attendance Requirements
All on-campus students are expected to attend scheduled classes - in some units, these classes are identified as a mandatory (pass/fail) component and attendance is compulsory. International students, on a student visa, must maintain a full time study load and meet both attendance and academic progress requirements in each study period (satisfactory attendance for International students is defined as maintaining at least an 80% attendance record).
Recommended Student Time Commitment
Each 6-credit Undergraduate unit at CQUniversity requires an overall time commitment of an average of 12.5 hours of study per week, making a total of 150 hours for the unit.
Class Timetable
Assessment Overview
Assessment Grading
This is a graded unit: your overall grade will be calculated from the marks or grades for each assessment task, based on the relative weightings shown in the table above. You must obtain an overall mark for the unit of at least 50%, or an overall grade of 'pass' in order to pass the unit. If any 'pass/fail' tasks are shown in the table above they must also be completed successfully ('pass' grade). You must also meet any minimum mark requirements specified for a particular assessment task, as detailed in the 'assessment task' section (note that in some instances, the minimum mark for a task may be greater than 50%). Consult the University's Grades and Results Policy for more details of interim results and final grades.
All University policies are available on the CQUniversity Policy site.
You may wish to view these policies:
- Grades and Results Policy
- Assessment Policy and Procedure (Higher Education Coursework)
- Review of Grade Procedure
- Student Academic Integrity Policy and Procedure
- Monitoring Academic Progress (MAP) Policy and Procedure - Domestic Students
- Monitoring Academic Progress (MAP) Policy and Procedure - International Students
- Student Refund and Credit Balance Policy and Procedure
- Student Feedback - Compliments and Complaints Policy and Procedure
- Information and Communications Technology Acceptable Use Policy and Procedure
This list is not an exhaustive list of all University policies. The full list of University policies are available on the CQUniversity Policy site.
Feedback, Recommendations and Responses
Every unit is reviewed for enhancement each year. At the most recent review, the following staff and student feedback items were identified and recommendations were made.
Feedback from SUTE unit comments report
Students complimented the delivery of live lectures in which students were able to communicate with the unit coordinator.
The unit coordinator should continue to deliver live lectures for better engagement and learning experiences.
- Apply key concepts of kinetics and kinematics to analyse machine design and synthesis
- Use analytical and graphical techniques to carry out position, velocity, and acceleration analysis
- Apply concepts of dynamics in balancing of rotating components
- Analyse vibrations in single and multiple degree of freedom systems
- Communicate professionally using relevant technical terminology, symbols, and diagrams and effectively document calculations and solutions
- Work autonomously and as a team member to analyse problems and present solutions.
The Learning Outcomes for this unit are linked with the Engineers Australia Stage 1 Competency Standards for Professional Engineers in the areas of 1. Knowledge and Skill Base, 2. Engineering Application Ability and 3. Professional and Personal Attributes at the following levels:
Intermediate
1.2 Conceptual understanding of the mathematics, numerical analysis, statistics, and computer and information sciences which underpin the engineering discipline. (LO: 1I 2I 3I 4I)
1.3 In-depth understanding of specialist bodies of knowledge within the engineering discipline. (LO: 1I 2I 3I 4I)
Advanced
1.1 Comprehensive, theory-based understanding of the underpinning natural and physical sciences and the engineering fundamentals applicable to the engineering discipline. (LO: 1A 2A 3A 4I)
1.4 Discernment of knowledge development and research directions within the engineering discipline. (LO: 1A 4A)
1.5 Knowledge of engineering design practice and contextual factors impacting the engineering discipline. (LO: 1A 4A)
1.6 Understanding of the scope, principles, norms, accountabilities and bounds of sustainable engineering practice in the specific discipline. (LO: 5A 6A)
2.1 Application of established engineering methods to complex engineering problem-solving. (LO: 1A 2A 3A 4A 6A)
2.2 Fluent application of engineering techniques, tools and resources. (LO: 4A)
2.3 Application of systematic engineering synthesis and design processes. (LO: 6A)
2.4 Application of systematic approaches to the conduct and management of engineering projects. (LO: 5A 6A)
3.2 Effective oral and written communication in professional and lay domains. (LO: 5A 6A)
3.4 Professional use and management of information. (LO: 5A 6A)
3.5 Orderly management of self, and professional conduct. (LO: 6A)
3.6 Effective team membership and team leadership. (LO: 6A)
Note: LO refers to the Learning Outcome number(s) which link to the competency and the levels: N – Introductory, I – Intermediate and A - Advanced.
Refer to the Engineering Undergraduate Course Moodle site for further information on the Engineers Australia's Stage 1 Competency Standard for Professional Engineers and course level mapping information https://moodle.cqu.edu.au/course/view.php?id=1511
Alignment of Assessment Tasks to Learning Outcomes
| Assessment Tasks | Learning Outcomes | |||||
|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | |
| 1 - Online Quiz(zes) - 20% | ||||||
| 2 - Written Assessment - 15% | ||||||
| 3 - Written Assessment - 20% | ||||||
| 4 - Practical Assessment - 15% | ||||||
| 5 - Portfolio - 30% | ||||||
Alignment of Graduate Attributes to Learning Outcomes
| Graduate Attributes | Learning Outcomes | |||||
|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | |
| 1 - Communication | ||||||
| 2 - Problem Solving | ||||||
| 3 - Critical Thinking | ||||||
| 4 - Information Literacy | ||||||
| 5 - Team Work | ||||||
| 6 - Information Technology Competence | ||||||
| 7 - Cross Cultural Competence | ||||||
| 8 - Ethical practice | ||||||
| 9 - Social Innovation | ||||||
| 10 - Aboriginal and Torres Strait Islander Cultures | ||||||
Textbooks
Design of Machinery
Edition: 6th edn ISE (2020)
Authors: Robert L. Norton
McGraw Hill
ISBN: 9781260590845
Binding: Paperback
Mechanical Vibrations
Edition: 6th edn (2017)
Authors: Singiresu S. Rao
Pearson Education
ISBN: 9781292178608
Binding: Paperback
IT Resources
- CQUniversity Student Email
- Internet
- Unit Website (Moodle)
All submissions for this unit must use the referencing style: Harvard (author-date)
For further information, see the Assessment Tasks.
j.sul@cqu.edu.au
l.piyathilaka@cqu.edu.au
Module/Topic
Introduction and Kinematics fundamentals
- Introduction to the unit and information session
- Introduction to the machine design and vibration
- Applications of kinematics
- DoF in 2D and types of motion
- Joints, links and kinematic diagrams
Chapter
Events and Submissions/Topic
Module/Topic
Graphical linkage synthesis
- Linkage synthesis - Graphical, manual and dimensional techniques with examples
- Two-position synthesis
- Three-position synthesis
Chapter
Events and Submissions/Topic
Module/Topic
Position analysis of linkages
- Types of motion
- Position analysis - Graphical, algebraic and vector loop methods for four-bar linkages and four-bar-crank slider
Chapter
Events and Submissions/Topic
Module/Topic
Analytical linkage synthesis
- 2 and 3 position motion generation by analytical and graphical synthesis
- 4 and 5 position motion generation using analytical synthesis
Chapter
Events and Submissions/Topic
Module/Topic
Velocity analysis of linkages
- Recap of Engineering Dynamics
- Graphical (vector) and instant centre methods (Kennedy's theorem)
- Mechanical advantages
Chapter
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
Acceleration analysis of linkages
- Graphical (vector) and analytical methods
- Coriolis acceleration
Chapter
Events and Submissions/Topic
Module/Topic
Dynamics fundamentals
- Lumped models
- Kinetics
- Virtual work
Chapter
Events and Submissions/Topic
Module/Topic
Static and Dynamic balancing
- Static and dynamic balancing on rotating masses
- Effect of balancing on shaking and input torque
Chapter
Events and Submissions/Topic
Module/Topic
Basic concepts of vibration
- Importance and types of vibration
- Natural frequency
- Critical damping and damping ratio
- Introduction to mathematical modelling and Laplace transform
Chapter
Events and Submissions/Topic
Module/Topic
Free and forced vibration
- Forced harmonic vibration and resonance
- Logarithmic decrement
- Support motion
- Rotating unbalance
Chapter
Events and Submissions/Topic
Residential School, 13 May
Module/Topic
Transient vibration
- Stability of a system
- Poles and Zeros
- Root Locus
- Bode plot
Chapter
Events and Submissions/Topic
Module/Topic
Two degree-of-freedom system
- 2 DoF undamped free vibration
- 2 DoF damped free vibration
- 2 DoF forced vibration
- 2 DoF translational and rotational
Chapter
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
Module/Topic
Chapter
Events and Submissions/Topic
1 Online Quiz(zes)
This assignment assesses students with the content from Week 1 to Week 4. You must provide detailed solutions to the problems given in the assignment in order to demonstrate your knowledge and understanding of the concepts and processes incorporating relevant sketches, clear step-by-step solutions and conclusion/judgement on answers.
1
Vacation Week Monday (8 Apr 2024) 11:59 pm AEST
You get unlimited attempts until the due date.
Students will get their results immediately after the due time, except for their sketches.
- Correctly identify the problem to be solved (key terms, units, elements, or parts of a problem)
- Choose the most appropriate approach to solving the problem
- Clearly present the solutions with sketches (if necessary) for the problems
- Attempt logical alternative approaches to solving the problem
- Apply key concepts of kinetics and kinematics to analyse machine design and synthesis
- Use analytical and graphical techniques to carry out position, velocity, and acceleration analysis
2 Written Assessment
Task 1: Design (or find) a 1 (or 2) DOF walking mechanism that is reasonably simple but still functional. You will need to assume the working condition of the walking mechanism, such as its walking speed, motor speed, and weight and materials of each link and the main body. This task will need to be completed concurrently with Task 2.
Task 2: Demonstrate the kinematic and kinetic analysis of the design of your choice. This task will need to be completed concurrently with Task 1.
Week 7 Monday (22 Apr 2024) 11:59 pm AEST
Peer and self-assessment task to be completed by Week 7
Week 8 Monday (29 Apr 2024)
Students to see feedback through the submission link.
You are required to assess your peers' interim reports as well as your own according to the following marking guidelines and are expected to provide sincere feedback and accurate marks for your peers. This is a valuable chance for reflection after viewing other submissions. 67% of this assessment will be from the marks from your peers and the rest will be from the quality of your feedback to your peers.
- Presentation (/20)
- Context and aims (/20)
- Design of a mechanism and kinematic diagram (/20)
- Kinematic analysis and verification process (/20)
- Discussions and conclusions (/10)
- Progress (/10)
- Apply key concepts of kinetics and kinematics to analyse machine design and synthesis
- Use analytical and graphical techniques to carry out position, velocity, and acceleration analysis
3 Written Assessment
Task 1: Design of a shock absorber system for a Segway patroller - Find the necessary stiffness and damping constant of the shock absorber system under the given conditions.
Task 2: Demonstrate the performance of your design - The new Segway patroller with your suspension system is to be tested on a rough road whose surface varies sinusoidally.
Week 11 Friday (24 May 2024) 11:59 pm AEST
Exam Week Friday (14 June 2024)
Students to see feedback through the submission link
- Presentation (/25%)
- Introduction and background (/15%)
- Methods and results (/25%)
- Discussion (/20%)
- Conclusions (/15%)
- Apply concepts of dynamics in balancing of rotating components
- Analyse vibrations in single and multiple degree of freedom systems
4 Practical Assessment
You are going to conduct three labs, namely Free vibration, Forced vibration, and Mass balance. After conducting these labs, you will complete each task given in the lab worksheet template. You don't need to give lengthy answers for the discussion tasks. You must show all workings where applicable. You must cite the sources of your argument and discussions as per the referencing style specified in the unit profile. This lab worksheet must NOT exceed 15 pages. You will submit it to the submission link provided in Moodle.
Week 12 Friday (31 May 2024) 11:59 pm AEST
Review/Exam Week Friday (7 June 2024)
Students to see feedback through the submission link
- Accurate results
- Accurate plots with correct axis titles and legends
- Appropriate discussions with supporting references
- Communicate professionally using relevant technical terminology, symbols, and diagrams and effectively document calculations and solutions
- Work autonomously and as a team member to analyse problems and present solutions.
5 Portfolio
Your final report will include Tasks 1 and 2 with further improvement from your interim report.
Task 3: Conduct vibration analysis of your design
Task 4: Verification of your analysis and Evaluation of your design
Exam Week Monday (10 June 2024) 11:59 pm AEST
Exam Week Friday (14 June 2024)
Students to see feedback through the submission link
The following criteria will be used to grade your report. This is not the suggested structure of your report.
- Innovation and creativity (/20%)
- Presentation (/20%)
- Introduction and background (/15%)
- Methods and results (/20%)
- Discussion (/15%)
- Conclusions (/10%)
- Apply concepts of dynamics in balancing of rotating components
- Analyse vibrations in single and multiple degree of freedom systems
- Communicate professionally using relevant technical terminology, symbols, and diagrams and effectively document calculations and solutions
- Work autonomously and as a team member to analyse problems and present solutions.
As a CQUniversity student you are expected to act honestly in all aspects of your academic work.
Any assessable work undertaken or submitted for review or assessment must be your own work. Assessable work is any type of work you do to meet the assessment requirements in the unit, including draft work submitted for review and feedback and final work to be assessed.
When you use the ideas, words or data of others in your assessment, you must thoroughly and clearly acknowledge the source of this information by using the correct referencing style for your unit. Using others’ work without proper acknowledgement may be considered a form of intellectual dishonesty.
Participating honestly, respectfully, responsibly, and fairly in your university study ensures the CQUniversity qualification you earn will be valued as a true indication of your individual academic achievement and will continue to receive the respect and recognition it deserves.
As a student, you are responsible for reading and following CQUniversity’s policies, including the Student Academic Integrity Policy and Procedure. This policy sets out CQUniversity’s expectations of you to act with integrity, examples of academic integrity breaches to avoid, the processes used to address alleged breaches of academic integrity, and potential penalties.
What is a breach of academic integrity?
A breach of academic integrity includes but is not limited to plagiarism, self-plagiarism, collusion, cheating, contract cheating, and academic misconduct. The Student Academic Integrity Policy and Procedure defines what these terms mean and gives examples.
Why is academic integrity important?
A breach of academic integrity may result in one or more penalties, including suspension or even expulsion from the University. It can also have negative implications for student visas and future enrolment at CQUniversity or elsewhere. Students who engage in contract cheating also risk being blackmailed by contract cheating services.
Where can I get assistance?
For academic advice and guidance, the Academic Learning Centre (ALC) can support you in becoming confident in completing assessments with integrity and of high standard.
What can you do to act with integrity?
