You will apply knowledge of equipment operation and use as well as radiographic image acquisition techniques to the optimisation of radiographic images and patient dose. You will perform quality control and quality assurance procedures to measure and maintain the performance of radiographic and ancillary equipment. You will investigate the impact of technical factor selection on patient dose and image quality. Through these you will learn to make informed selections of technical parameters for radiographic procedures and to justify your decision-making.
|Student Contribution Band||SCA Band 2|
|Fraction of Full-Time Student Load||0.125|
|Pre-requisites or Co-requisites||
MEDI12001 Radiation Science and MEDI12002 Science and Instrumentation 1
MEDI12004 Medical Imaging Clinical Course 1
MEDI12005 Science & Instrumentation 2
Important note: Students enrolled in a subsequent unit who failed their pre-requisite unit, should drop the subsequent unit before the census date or within 10 working days of Fail grade notification. Students who do not drop the unit in this timeframe cannot later drop the unit without academic and financial liability. See details in the Assessment Policy and Procedure (Higher Education Coursework).
|Class Timetable||View Unit Timetable|
|Residential School||No Residential School|
All on-campus students are expected to attend scheduled classes – in some units, these classes are identified as a mandatory (pass/fail) component and attendance is compulsory. International students, on a student visa, must maintain a full time study load and meet both attendance and academic progress requirements in each study period (satisfactory attendance for International students is defined as maintaining at least an 80% attendance record).
Each 6-credit Undergraduate unit at CQUniversity requires an overall time commitment of an average of 12.5 hours of study per week, making a total of 150 hours for the unit.
|1. Practical and Written Assessment||40%|
|2. In-class Test(s)||60%|
This is a graded unit: your overall grade will be calculated from the marks or grades for each assessment task, based on the relative weightings shown in the table above. You must obtain an overall mark for the unit of at least 50%, or an overall grade of ‘pass’ in order to pass the unit. If any ‘pass/fail’ tasks are shown in the table above they must also be completed successfully (‘pass’ grade). You must also meet any minimum mark requirements specified for a particular assessment task, as detailed in the ‘assessment task’ section (note that in some instances, the minimum mark for a task may be greater than 50%).
All University policies are available on the Policy web site, however you may wish to directly view the following policies below.
This list is not an exhaustive list of all University policies. The full list of policies are available on the Policy web site .
Term 2 - 2020 : The overall satisfaction for students in the last offering of this course was 3.8 (on a 5 point Likert scale), based on a 29.09% response rate.
Every unit is reviewed for enhancement each year. At the most recent review, the following staff and student feedback items were identified and recommendations were made.
On successful completion of this unit, you will be able to:
Medical Radiation Practice Board of Australia's Professional Capabilities Standards:
Domain 1: 3. Assume responsibility and accept accountability for clinical decisions.
Domain 3: 1. Apply critical and reflective thinking to resolve clinical challenges.
Domain 4: 1. Implement safe radiation practice appropriate to their division of registration. 2. Confirm and operate equipment safely and appropriate to their division of registration. 3. Maintain safety of self and others in the work environment appropriate to their division of registration. 4. Safely manage radiation and radioactivity in the environment.
Domain 5: 2. Apply principles of medical radiation physics and instrumentation.
|Assessment Tasks||Learning Outcomes|
|1 - Practical and Written Assessment||•||•||•|
|2 - In-class Test(s)||•||•||•||•||•|
|Graduate Attributes||Learning Outcomes|
|1 - Communication||•||•||•||•|
|2 - Problem Solving||•||•||•||•||•|
|4 - Information Literacy||•||•||•||•|
|6 - Information Technology Competence||•||•||•||•|
|8 - Ethical practice||•|
|Assessment Tasks||Graduate Attributes|
|1 - Practical and Written Assessment||•||•||•||•|
|2 - In-class Test(s)||•||•||•||•||•|